After you tighten it, then you can release the spring compressors. Again, the service manual says to tighten the rear suspension with the weight of 1 person in the rear. It is designed to fit a wide range of stereos and vehicle models. Compress the spring with a spring compressor and disassemble. We believe in helping you find the product that is right for you. But because they're so soft and combined with worn bushings, worn shocks result in a poor ride.
Replacing the starter itself from the engine is relatively straightforward, but it helps to remove the battery box for better access. Repeat for the other side. While still compressed, put your springs onto the new shock. I'm considering just removing the locking clips the next time I have the unit out. I reserved it online and picked it up in store the same day.
If you counterhold then the strut shaft will just spin and you won't loosen anything. Or just taping them in the released position. If your car has high mileage or other problems are detected, also consider the bump stops, ball joints, sway bar endlinks, and lower control arm's front bushing. The starter motor will wear out over time. Caution: As a rule of thumb, always tighten all suspension components in their normal resting position not extended or fully compressed! The most important thing to do before anything else is to remove the negative lead from the battery. Always point the spring and strut away from yourself so that if it does fail, it doesn't hit you! You need access to these for the next step.
The socket is there because Autozone's free loaner with deposit compressor is too long. Front strut replacement Take off the front wheels. The part number for my right-side tie rod was 1J0422804B. You can use an impact wrench to zip off the nut but don't use it to tighten the nut! Here's a great tip: Any time I buy a new car, I go to Firestone a local garage and buy a lifetime alignment package. Make sure it doesn't shift off the jack stands! If you can see the metal piston, consider changing the boot because the boot serves to protect the seals from dirt. The rest of installation is the reverse of removal. Support the subframe's weight with a jack while you loosen the bolts.
So call your local auto shop for more details on renting. The Bentley says to remove the axle on the pass side. There are six plastic snaps holding the door card, pull up and out to pull these out. Once the strut assembly is out of the car, use 2 spring compressors on opposite sides to compress the spring. Summary: remove the bolts securing the struts and remove the strut assembly from the car. With the unit still inside, use a small screwdriver to carefully pry up.
Bump stops are rubber bumpers at the top of the shock. Drive around for a day or two to let the suspension settle in. If you have an impact wrench, you can use it for removal but don't use it for tightening that nut! It can also develop a grinding noise, indicating that the bearings in the starter are failing. Or are they just where the slots are located? Here is a basic animation I made depicting how it works. Save yourself the trouble and use a zip tie for the inner and outer boot clamps. It's just a fact of life. Then chock the wheels, apply the parking brake, and make sure the car is safe and secure before working on it! The advantage of the metalnerd tool is that it has a square cutout for adapting a torque wrench always mate at 90o angle! When you pull on the clips, etc.
This can be done by raising the rear suspension arm to a slightly loaded position like shown below. Replace the heat shield or wires as needed. For New Beetle only: the strut tops are under a cover. If it bounces and returns in one or two bounces, it is probably in good shape. New strut mounts are recommended.
It is always recommended to have an alignment after you change tie rods. You will want to keep your new outer tie-rod screwed on to the same length as the old. The front suspension components should be tightened in their normal resting position - not fully extended and not fully compressed. This article is not a substitute for the factory service manual or the services of a professional mechanic. Pictured below is the rear door. Just follow the same shape as the tools seen in the above graphic, worked great for me using my expired credit card! Popular tool mk4 of Good Quality and at Affordable Prices You can Buy on AliExpress. Use hand tools to tighten.