The pin has a handle on the top. This means that these types of 2006 Mercury Montego headlights do not have to be adjusted in the same way that older 06 Mercury Montego headlights do. This will shorten the life of the bulb. On such vehicles the entire auto headlight assembly can be adjusted to the left or right as well as up and down. If you happen to touch the glass part of the headlight bulb, clean it with rubbing alcohol. That's the only thing that locks it in place.
The bulb should pull out now. In addition, any time you are driving in fog it is important to use your headlights to help you see what is in front of you. There are two more wing nuts just like the first one that hold the headlight assembly in place on top of the radiator support. Find an inventory of used 2006 Mercury Montego car and truck parts from 100+ top auto dismantlers, modern junkyards and used parts dealers. This is what holds the builb into place.
Push the covers back on. Install in reverse, be careful not to touch the glass part of the new bulb with your fingers. Auto headlight assemblies which were manufactured several years ago typically utilized 2006 Mercury Montego headlights which were self-contained, meaning the entire assembly had to be replaced if the 06 Mercury Montego headlights went out. Those are the only things that actually lock it into place. .
Pull the bulb straight out. Therefore, if you have had problems with the 2006 Mercury Montego headlights it is important to get the problem looked at and to have the 06 Mercury Montego headlights replaced if necessary. After removing that nut persuade the side marker light to slide forward. Having a problem with your car headlights means you are not as capable of seeing well at night or in bad weather. Pry from the inside end of the lens assembly to unseat the other guide pin. Untwist the socket to replace the turn signal bulb.
There is a clip holding the connector onto the light that will have to be lifted while pulling connector off. Conversely, newer 06 Mercury Montego headlights do not suffer from this shortcoming, as they consist of a bulb that is fixed in one location with a clear cover over it. Feb 28, 2011 Lift hood, disconnect connector going to back of light fixture. If a problem occurs the bulb that is in question can be replaced, leaving the others untouched. Push them in together so that the cover releases. There will be a retaining ring around were you pulled the connector turn it counter clockwise. Regardless of the type of automobile headlights that are used on your vehicle it is important to ensure that they are in good working condition.
This is especially true for older vehicles which utilize single, self-contained auto headlight assemblies. Buy 2006 Mercury Montego salvage parts directly from the sourcing wrecking yard! Push the retaining pin all the way back down into place. Open the S60's hood and locate the pin that is behind the headlight assembly of the bulb that needs replacement. Push the visible wire aside. Unscrew that wing nut to remove the side marker light. The clamps are on either side.
Or simply remove the bulb by twisting the harness and retaining ring counterclockwise and remove it as an assembly. However, newer vehicles use a single light bulb and the 2006 Mercury Montego headlights can be replaced by removing the cover and installing a new bulb. Once you slide it up off the studs the wing nuts were on. At the top between the turn signal and headlight there is a black plastic wing nut. These types of auto headlight assemblies must be adequately adjusted in order to be sure that the lights track straight down the road and allow you to see where you are going. Another key component of being able to see adequately when you are using 2006 Mercury Montego headlights is to be sure that they are adjusted properly. Push on the back of the headlight assembly until it comes out the front of the S60.
Unplug the plug from the back of the light use a flat screwdriver to lift the tab a little. Once you have located the correct 2006 Mercury Montego headlights for your automobile you can remove the old 06 Mercury Montego headlights and install the new ones. Reconnect the electrical harness to the assembly and push the assembly back into place. We offer free shipping and low-price guarantee. The black plastic piece the headlight is mounted to Remove these two wing nuts and lift up on the whole assembly. Since that is out now. There is an electrical connection on the back of the assembly; unplug the connection.
Therefore, you should turn your automobile's headlights on and make sure they are set on low beam so that you can better see what is in your path of travel. Twist the round plastic ring that holds the bulb in. Locate the transmission after locating look for a tube with a dipstick in in make sure after you pull the stick the fluid is a red color it will say trans fluid with the car running and after removal of the stick wipe it clean replace it in the tube and remove it again the levels are marked on the stick Sep 17, 2012. Press on both clamp on the assembly. Pull the pin straight out of the headlight assembly.