2001 intrigue crankshaft position sensor. SOLVED: Crankshaft sensor location on 2001 oldsmobile 2019-04-30

2001 intrigue crankshaft position sensor

How to Install a Crankshaft Sensor in a 2000 Olds Intrigue

2001 intrigue crankshaft position sensor

Here is a diagram for you. My gas pedal is sticking now this just start happening. The first time it cut off while I was driving and the second time it cut off while I was at a traffic light. Starter must be removed first. Replace, and make sure it is pushed in all of the way. It's now easier and you can now remove the sensor with the harness attached. Here is a diagram for you.

Next

Crankshaft Position Sensor Problems of the 2001 Oldsmobile Intrigue

2001 intrigue crankshaft position sensor

After washing the plug out with spray brake cleaner, blow out with compressed air to get rid of the oil. Recently my car is having a hard time starting but more importantly, my car will stall while I'm driving! The sensor picks up the signal direct off of the crankshaft through a machined hole in the engine block. It's on the top rear of the engine, behind the intake manifold. On electrical problem, battery would run down after car left sitting for 3-4 days in cold weather. Remove the small plastic shield from the bottom of the motor, where the motor meets the transmission housing.

Next

Oldsmobile Intrigue Crankshaft Position Sensor Problems

2001 intrigue crankshaft position sensor

Insert the new sensor into the engine, with the outer angled section of the sensor facing upward. There is a large wiring harness bracket attached to the transmission bell housing that was temporarily unbolted to aid with the removal and installation of the crank sensor. I bought the car from a used lot in Aug 2014, shortly after I received a recall notice. Do not over-tighten the bolt or you may ruin the new crankshaft position sensor. Needed to replace faulty crankshaft sensor. The sensor has 1 bolt holding it in. Pull off the valve cover breather hose with the air tube.

Next

How to Install a Crankshaft Sensor in a 2000 Olds Intrigue

2001 intrigue crankshaft position sensor

There were times, when the consumer removed the key from the ignition and the engine would continue to run. Oldsmobile was founded in 1897 by Ransom E. Lift the front of the Intrigue off of jack stands, then remove the stands from beneath the car. That is ths sucker that has leaked oil into the plug and has caused the P0335 code. Simply pulling on the wires won't work, and could damage your plug. There's an O-ring on the sensor that prevents it from coming out easily, although it will rotate in place. With the light down there and you looking down between the intake manifolds and working with your right hand, it's not that bad.

Next

Oldsmobile Intrigue Crankshaft Position Sensor Problems

2001 intrigue crankshaft position sensor

I recommend that you loosen the bolt with the socket, then reach your hand around to the connector and remove the bolt by hand. After numerous attempts to start the vehicle, he had it jumpstarted. In addition, the instrument panel indicators would illuminate at random. It … isn't too bad of a job, I did it in the unheated garage at 0F For the 1. Lower the Intrigue to the ground.

Next

SOLVED: Crankshaft sensor location on 2001 oldsmobile

2001 intrigue crankshaft position sensor

Jul 08, 2010 Like a lot of people. I just did my 2005 Altima 4 cyc. I have to jiggle with the switch a few times in order for the window on driver side to go down. It is located in the driver's side portion of the head facing the wheel. It isn't too bad of a job, I did it in the unheated… On a 2000 Oldsmobile Intrigue with a 3. I had the vehicle thoroughly checked by a mechanic and I was told that it was an electrical issue this is a safety issue. The information below is compiled of tips I found on the inter … net and my own experience.

Next

Oldsmobile Intrigue Crankshaft Position Sensor Problems

2001 intrigue crankshaft position sensor

A recent problem developed, where the consumer was unable to turn the vehicle off. Claimed it belonged to gm. Remove the O-ring if it still is mounted in the mounting hole. Only a couple of things I did different which may be of added benefit. The vehicle lost all electrical power and power steering ability.

Next

Where is crankshaft position sensor on 2001 olds intrigue

2001 intrigue crankshaft position sensor

Disconnect the negative battery cable. The motor needs to be installed exactly as it is removed. The replacement sensor will be a metal cylinder and installs 180 degrees backward, allowing future access to the bolt so that the sensor can be removed before unplugging it. Dealer would not repair --out of warranty. These will let you know more about which areas to look, check, when there is engine light coming up on dash panel. Remove the fro … nt right tire and place firmly on jackstands.

Next

Cam Position Sensor: Vehicle Had No Loss of Power, No Stalling ...

2001 intrigue crankshaft position sensor

Remember to reinstall all brackets and items that were removed. Make a mental note of the position of the starter solenoid, above the starter motor. Would recharge battery and it would be ok. Recently, the abs, brake light and traction light illuminated. . Its above the starter going into the side of the block. After numerous attempts to start the vehicle, he had it jumpstarted.

Next